Learn which materials are compatible with Cricut StickerPix Print + Cut and how to load, handle, and store them for best results.
Compatible materials and ink for Cricut StickerPix Print + Cut
Depending on the bundle you purchased your Cricut StickerPix Print + Cut may include:
| Item | Description |
| Photo Paper, 18 sheets | A glossy white sheet with perforated tear-off strips on each end. Used to print photos, photo collages, photo cards & invitations. |
| Sticker Sheets, 18 sheets | A glossy white sheet backed with adhesive and a liner. No perforations or tear-off sections. Used to make custom sticker sheets and labels. |
| Ink Cartridge (good for 36 prints) | Contains the ink colors (CMY) + clear laminate film that are applied in four layers during printing. |
When purchasing materials, make sure to purchase only Cricut StickerPix Print + Cut refill sets. Available packs may vary by retailer and region, and include:
| Description | Contents |
StickerPix Print + Cut – Sticker Sheets Glossy, White 4 in x 7 in | 72 sticker sheets + 2 ink refills |
StickerPix Print + Cut – Photo Paper Glossy, White 4 in x 6 in | 72 sheets photo paper + 2 ink refills |
StickerPix Print + Cut – Sampler Sticker, Glossy, White 4 in x 7 in Photo Paper, Glossy, White 4 in x 6 in | 36 sticker sheets + 36 sheets photo paper 2 ink refills |
Are materials from other companies compatible with Cricut StickerPix Print + Cut?
Cricut StickerPix Print + Cut is calibrated for Cricut ink and paper. Third-party consumables may cause clogging, print defects, or machine damage. Cricut cannot guarantee results of machine health & performance if third-party supplies are used.
How to replace the ink cartridge for StickerPix Print + Cut
To replace the ink cartridge:
- Open the cartridge access door (Door A) and lift the lock to release the used ink cartridge.
- Insert the new ink cartridge with the printed label facing up. Push the cartridge in until it locks into place.
- Close the cartridge access door.
Important: Avoid touching the film. Fingerprints and natural oils from your fingers will transfer to the film and may appear on the final print. Handle the ink cartridge by touching the hard plastic areas only.
How to load the Material Tray for StickerPix Print + Cut
Remove the material tray from the storage slot.
Lift the tray cover.
Load material into the tray, printing side up. Use the adjustable material guide to ensure the right fit.
Important: To ensure quality, do not touch the printing side of the material.
For Photo Paper, the material guide should sit at the 4 x 6” position.
(*Do not remove Photo Paper tear-off strips until after printing – they are necessary to help feed the material through the machine.)
For Sticker Sheets, move the guide to the 4 x 7” position.
Close material tray cover.
Insert the material tray into the material tray slot, which is directly below the material tray storage. Push until the tray clicks into place.
Material Tray capacity: One (1) packet of materials which is 18 sheets.
Note: When not in use, place the material tray in the material tray storage slot and close the machine door.
Care, Handling, and Storage of Photo Paper, Sticker Sheets, and Ink Cartridges
Keep Cricut StickerPix Print + Cut materials clean and protected to help maintain print quality and machine performance.
Handling Materials
- Avoid touching printable surfaces. Oils and fingerprints can affect print quality. Avoid touching the printable surface of unprinted materials or the ink film.
- Remove dust with compressed air. If materials or the Material Tray are exposed to dust or airborne particles, use compressed air to clean them before use.
- Avoid liquids and cleaners. Do not use water, solvents, or household cleaners on unprinted materials.
Storing Materials
Keep materials in a cool, dry place away from direct sunlight and humidity. The optimal paper storage environment is below 86°F (30°C) with relative humidity under 80%. Printing quality may be affected if the environmental temperature and humidity are not appropriate.
When not in use, store materials in:
- Their original packaging. Cut across the very top of the original plastic bag with scissors so you can reuse it for storage.
- A clean, hard-sided container with a secure lid.
- The Material Tray in the storage position.
Important: Do not store opened materials in zippered plastic storage bags, as they may damage the material.