Learn which materials are compatible with Cricut StickerPix Print and how to load, handle, and store them for best results.
Compatible materials and ink for Cricut StickerPix Print
Depending on the bundle you purchased your Cricut StickerPix Print may include:
| Item | Description |
| Photo Paper, 18 sheets | A glossy white sheet with perforated tear-off strips on each end. Used to print photos, photo collages, photo cards & invitations. |
| Sticker Sheets, 18 sheets | A glossy white sheet with adhesive and a liner, along with removable strips on each end. Used to print photos, photo collages, photo cards & invitations. |
| Sticker Paper, Pre-Cut Circles, 18 sheets | A glossy white sheet backed with adhesive and a liner, with pre-cut circle stickers. Used to make custom circle stickers and labels. |
| Sticker Paper, Pre-Cut Rectangles, 18 sheets | A glossy white sheet backed with adhesive and a liner, with pre-cut rectangle stickers. Used to make custom rectangle stickers and labels. |
| Sticker Paper, Pre-Cut Squares, 18 sheets | A glossy white sheet backed with adhesive and a liner, with pre-cut square stickers. Used to make custom square stickers and labels. |
| Ink Cartridge (good for 54 prints) | Contains the ink colors (CMY) + clear laminate film that are applied in four layers during printing. |
When purchasing materials, make sure to purchase only Cricut StickerPix Print materials. Available refill sets may vary by retailer and region, and include:
| Description | Contents |
StickerPix Print – 4x6 Stickers & Photo Kit Photo Paper, Glossy, White 4 in x 6 in (36) Sticker Sheets, Glossy, White 4 in x 6 in (18) | 36 sheets photo paper + 18 sticker sheets + 1 ink refill |
StickerPix Print – Sticker Sheet Pre-Cut Kit Sticker Sheets, Pre-Cut Rectangles, Glossy, White 4 in x 6 in (18) Sticker Sheets, Pre-Cut Circles, Glossy, White 4 in x 6 in (18) Sticker Sheets, Pre-Cut Squares, Glossy, White 4 in x 6 in (18) | 54 sticker sheets + 1 ink refill |
Are materials from other companies compatible with Cricut StickerPix Print?
Cricut StickerPix Print is calibrated for Cricut ink and paper. Third-party consumables may cause clogging, print defects, or machine damage. Cricut cannot guarantee results of machine health & performance if third-party supplies are used.
How to replace the ink cartridge for StickerPix Print
To replace the ink cartridge:
- Open the cartridge access door (Door B) and lift the lock to release the used ink cartridge.
- Insert the new ink cartridge with the printed label facing up. Push the cartridge in until it locks into place.
- Close the cartridge access door.
Important: Avoid touching the film. Fingerprints and natural oils from your fingers will transfer to the film and may appear on the final print. Handle the ink cartridge by touching the hard plastic areas only.
How to load the Material Tray for StickerPix Print
Lift the Material Tray off the top of the printer.
Slide out and flip the cap (part A) underneath the Material Tray until it secures in place.
Lift the lid (part B). Load the material into the tray, printing side up.
Important: To ensure quality, do not touch the printing side of the material.
(*Do not remove Photo Paper tear-off strips until after printing – they are necessary to help feed the material through the machine.)
Important: When using sticker sheets, load one sheet at a time.
Close the lid and lower the kickstand beneath the Material Tray. Make sure both are securely in place before proceeding.
Open Machine Door, then insert Material Tray into Material Tray Slot. Push until the tray clicks into place.
Load limit: Photo Paper, up to ten (10) sheets. For sticker sheets, load one (1) Sticker Sheet at a time.
Note: When not in use, place the material tray on top of the printer and close the machine door.
Care, Handling, and Storage of Photo Paper, Sticker Sheets, and Ink Cartridges
Keep Cricut StickerPix Print materials clean and protected to help maintain print quality and machine performance.
Handling Materials
- Avoid touching printable surfaces. Oils and fingerprints can affect print quality. Avoid touching the printable surface of unprinted materials or the ink film.
- Remove dust with compressed air. If materials or the Material Tray are exposed to dust or airborne particles, use compressed air to clean them before use.
- Avoid liquids and cleaners. Do not use water, solvents, or household cleaners on unprinted materials.
Storing Materials
Keep materials in a cool, dry place away from direct sunlight and humidity. The optimal paper storage environment is below 86°F (30°C) with relative humidity under 80%. Printing quality may be affected if the environmental temperature and humidity are not appropriate.
When not in use, store materials in:
- Their original packaging. Cut across the very top of the original plastic bag with scissors so you can reuse it for storage.
- A clean, hard-sided container with a secure lid.
- The Material Tray in the storage position.
Important: Do not store opened materials in zippered plastic storage bags, as they may damage the material.